Washing machines often shake because the mass of clothes is distributed unevenly inside of them. Always make sure to spread out the clothes throughout your washer as you load it. If your washer continues to shake, remove some of your clothes. You may have simply overloaded it. If your washer consistently causes your clothes to bundle together into an uneven ball, the drum is probably absorbing weight unevenly because it isn’t level.

Top-loading machines can typically handle more clothing. If you’re in the market for a new washer, opt for a top-loading machine if you can. Overfilling your machine will also keep your clothes from getting adequately clean.

If your dryer is unlevel too, then it’s probably your floor’s fault. Try finding a flatter area of your home to set the machines or slide a sheet of plywood underneath them.

The shipping bolts ensure that your drum doesn’t move during delivery and installation. They will cause a machine to shake if they’re left in. Depending on the make and model of your machine, the shipping bolts may be hiding behind the back panel. If your back panel simply slides out, lift it up to see if there are any plastic pieces latched to your drum.

The shipping bolts are usually brightly-colored so that they’re easy to notice. They also tend to be made from a cheap plastic. They should look really out of place on your machine.

It is better to raise a leg than lower one, so adjust the leg that is too high. Newer machines typically don’t have adjustable legs in the back.

If your machine isn’t stable as it rests on the block, add another block next to your first block to distribute the weight more evenly. You can use a brick or other solid object if you don’t have a block of wood.

Some newer machines don’t use a locking bolt. You simply adjust the leg by turning it and you don’t need to worry about locking it. {“smallUrl”:“https://www. wikihow. com/images/thumb/4/4f/Fix-a-Shaking-Washing-Machine-Step-9. jpg/v4-460px-Fix-a-Shaking-Washing-Machine-Step-9. jpg”,“bigUrl”:"/images/thumb/4/4f/Fix-a-Shaking-Washing-Machine-Step-9. jpg/aid285204-v4-728px-Fix-a-Shaking-Washing-Machine-Step-9. jpg",“smallWidth”:460,“smallHeight”:345,“bigWidth”:728,“bigHeight”:546,“licensing”:"<div class="mw-parser-output">

\u00a9 2023 wikiHow, Inc. All rights reserved. wikiHow, Inc. is the copyright holder of this image under U. S. and international copyright laws. This image is not</b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n</p>

<br />\n</p></div>"} You can use trial and error by lowering the legs and checking the level again, or your can try to measure each leg with a measuring tape. You may not be able to visually determine if the legs are even.

Use a levelling tool so you’ll be able to set the washer straight on each side.

If the back legs are level, tap each leg in the back 2-3 times with your wrench or channel locks. There may be a little rust or dirt stuck in the self-leveling joint. If your control panel is round on top or set at an angle, place your level directly in front of it.

You can also spray the legs with a little bit of machine or hinge lubricant. Wipe off the excess lubricant after you’ve applied it to the leg near the connection to the frame.

The shock absorbers are small coils or pistons that absorb the vibration from your drum when it’s spinning. They also connect the drum to the frame of the machine. There are either 2, 4, or 5 of them depending on your model. The model and brand are usually listed on the front, but they may be printed on a metal plate on the back of the machine or inside of the door. Some newer models require a professional to install new shock absorbers. Read your machine’s manual to see if you can take the front panel off to access the shock absorbers.

The water lines are usually thin and made of rubber. They often have a blue and red valve on top of them near the connection to the frame.

If your remove the bottom panel on a top-load washer and see a spring rolling around, your suspension rod fell off. Hook it back into the center of your drum and put the machine back. This was causing the noise and shaking. {“smallUrl”:“https://www. wikihow. com/images/thumb/b/b5/Fix-a-Shaking-Washing-Machine-Step-17. jpg/v4-460px-Fix-a-Shaking-Washing-Machine-Step-17. jpg”,“bigUrl”:"/images/thumb/b/b5/Fix-a-Shaking-Washing-Machine-Step-17. jpg/aid285204-v4-728px-Fix-a-Shaking-Washing-Machine-Step-17. jpg",“smallWidth”:460,“smallHeight”:345,“bigWidth”:728,“bigHeight”:546,“licensing”:"<div class="mw-parser-output">

\u00a9 2023 wikiHow, Inc. All rights reserved. wikiHow, Inc. is the copyright holder of this image under U. S. and international copyright laws. This image is not</b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. This image may not be used by other entities without the express written consent of wikiHow, Inc.
\n</p>

<br />\n</p></div>"} Remove the bottom panel on a top-load washer. You’ll have to tilt the machine on its side to do this. Keep the case from getting scratched by laying a rug or towel out before doing this.

Some shock absorbers have pins locking them to the drum and the frame. If any of the pins fell out, simply slide them back in. This was probably the cause of your shaking. If you have 5 absorbers, 1 of them is probably in the back. You may not be able to reach this piece without professional assistance.

Replacing the drum in a washing machine is often not worth it, and you should consult a washing machine repair company to determine the price of the repair. It is not typically a problem that a non-professional can solve.